☆ 面板操作方法：

1. 开机（power on），按RESET
2. SETUP（出现1234）
3. ENTER（出现C000为密码正确；出现E000则为密码错误，此时先按ENTER，再将密码设置成通用密码8888，再按RESET，重复第2步操作）
4. 再按一次ENTER，出现d-01（表示晶震为1）
5. 再按一次ENTER，出现C-01（表示ID地址）
6. 再按一次ENTER，出现dy-1（表示报警时长为1）
7. 再按一次ENTER，出现1-XX（1表示第1区，XX表示此区灵敏度数值）此时可以开始设置各区灵敏度，按SETUP切换不同区，按ESC调节灵敏度；1至6区位的数值越高，则其灵敏度越高；第7区代表整台门的灵敏度，有h1，h2，h3三个选项，其中h3灵敏度最高，h1最低。
8. 设置完毕后按ENTER, 再按RESET键结束操作。

☆ 遥控器操作方法：

1. POWER，按RESET
2. PROG（出现1234）
3. ENTER（出现C000为密码正确；出现E000则为密码错误，此时先按ENTER，再将密码设置成通用密码8888，再按RESET，重复第2步操作）
4. 再按一次ENTER，出现d-01（表示晶震为1）
5. 再按一次ENTER，出现C-01（表示ID地址）
6. 再按一次ENTER，出现dy-1（表示报警时长为1）
7. 再按一次ENTER，出现1-XX（1表示第1区，XX表示此区灵敏度数值）此时可以开始设置各区灵敏度，按PROG切换不同区，按ESC调节灵敏度；1至6区位的数值越高，则其灵敏度越高；第7区代表整台门的灵敏度，有h1，h2，h3三个选项，其中h3灵敏度最高，h1最低。
8. 设置完毕后按ENTER, 再按RESET键结束操作。

DEBUGGING OF IRON KINGKONG SERIAL GG-III， GG-LED WALK THROUGH METAL DETECTOR

☆ Panel Control:

1. POWER ON, PRESS RESET
2. SETUP (Showing “1234”)
3. ENTER (Showing “C000” means password correct; Showing “E000” means password incorrect, press ENTER, change the password to the common one “8888”, press RESET, go back to the second step.
4. Press ENTER, showing “d-01” (means Frequency Span is 1)
5. Press ENTER, showing “C-01” (means the ID address is 01)
6. Press ENTER, showing “dy-1” (means alarming time is 1)
7. Press ENTER, showing “1-XX” (“1” refers to the zone 1, ”XX” refers to the sensitivity of this zone), then you can begin to set the sensitivity of each zone. Press SETUP to switch between differtent zones, press SELECT to adjust sensitivity; the larger digital zone 1 to zone 6 shows, the higher sensitivity you get; zone 7 refers to the sensitivity of the whole check gate, we get h1，h2，h3 here, h3 has the highest sensitivity and h1 has the lowest.
8. Finally press ENTER, and press RESET to finish debugging.

☆ Remote Control:

1. POWER ON, PRESS RESET
2. PROG (Showing “1234”)
3. ENTER (Showing “C000” means password correct; Showing “E000” means password incorrect, press ENTER, change the password to the common one “8888”, press RESET, go back to the second step.
4. Press ENTER, showing “d-01” (means Frequency Span is 1)
5. Press ENTER, showing “C-01” (means the ID address is 01)
6. Press ENTER, showing “dy-1” (means alarming time is 1)
7. Press ENTER, showing “1-XX” (“1” refers to the zone 1, ”XX” refers to the sensitivity of this zone), then you can begin to set the sensitivity of each zone. Press PROG to switch between differtent zones, press ECS to adjust sensitivity; the larger digital zone 1 to zone 6 shows, the higher sensitivity you get; zone 7 refers to the sensitivity of the whole check gate, we get h1，h2，h3 here, h3 has the highest sensitivity and h1 has the lowest.
8. Finally press ENTER, and press RESET to finish debugging.

铁金刚系列GG-LCD安检门使用及调试方法
1. 开机（power on），出现PASS 001, ALARM 001（通过001，报警001）

1. PROG（编程），出现INPUT PASSWORD ”****”）
2. ENTER出现MENU（菜单）
3. 按LEFT或者RIGHT选择2.SENSITIVITY LEVEL（灵敏度），按ENTER进入
4. 出现1-85（1表示第1区，85表示此区灵敏度数值），此时可以开始设置各区灵敏度，按LEFT或者RIGHT切换区，按UP或者DOWN调节灵敏度；1至6区位的数值越高，则其灵敏度越高；第7区代表整台门的灵敏度，有LOW，MID，HIG三个选项，其中HIG灵敏度最高，LOW最低。
5. 设置完毕后按ENTER，再按RESET键结束操作。

DEBUGGING OF IRON KINGKONG SERIAL GG-LCD WALK THROUGH METAL DETECTOR

1. POWER ON, (Showing “PASS 001, ALARM 001”)
2. PROG, (Showing “INPUT PASSWORD ****”)
3. ENTER, (Showing the operation menu)
4. Press LEFT or RIGHT to select “2.SENSITIVITY LEVEL”,press ENTER to enter this item.
5. Showing “1-85” (“1” refers to zone 1, “85” refers to the sensitivity of this zone. Then you can begin to set the sensitivity of different zones. Press LEFT or RIGHT to swicth between different zones, Press UP or DOWN to adjust sensitivity; the larger digital zone 1 to zone 6 shows, the higher sensitivity you get; zone 7 refers to the sensitivity of the whole check gate, we get LOW, MID, and HIG here, HIG has the highest sensitivity and LOW has the lowest.
6. Finally press ENTER, and press RESET to finish debugging.

附：常用灵敏度设置 (Most common used settings)

1. 高灵敏度, 工厂设置（可准确探测一枚一元硬币）High Sensitivity, Use in Factory(can detect a coin)
1-95
2-99
3-99
4-99
5-99
6-80
7-h2/MID

2. 低灵敏度, 娱乐场所设置（可排除手机，钥匙等小件物品）Low Sensitivity, Use in Court(can exclude keys, mobiles)
1-05
2-10
3-10
4-10
5-10
6-05
7-h1/HIG